Description:

Like New BRANDT KDN 650 C Optimat Automatic Edgebander (2003)

!!! ONLY 802 HRS, LIKE NEW…MAKE AN OFFER !!!

PC-16 Program Control:
- Color matrix LCD screen display
- 8mb RAM
- Manual push button controls or program control operation
Equipped with digital height indicator.
Integrated electronic line control system for increased reliability and diagnostic assistance. No limit switches used for setting operating units.
Control panel located at machine infeed for operator convenience.
Universal automatic magazine for strip and coil feeding.
Large coil table (800 mm diameter) to accommodate large coils of 3 mm PVC.
Hot melt granulate glue application system with twelve minute heat-up time.
Quick-change glue tank for easy maintenance and glue color change, if necessary.
Reversible rotation of glue application roller. Retractable glue roller.
Strengthened precutter for cutting PVC (max. 3 x 45 mm) from the coil.
Infrared radiant quartz heating unit between glue roller and pressure zone for optimum gluing strength.
First pressure roller driven and two idle pressure rollers.
Double motor end trimming unit with straight and chamfer capability. Chamfer up to 15?. Program controlled indexing from straight to bevel end trimming.
Fine trimming unit with digital “Quickset” system. Tilt range 0 - 25?. Program controlled indexing.
Contour trimming unit for profile corner trimming.
Sound enclosure with centralized dust extraction outlet.
Scraping unit for rigid PVC edges. Program controlled indexing.
Buffing unit.
Electronic frequency changer for all trimming motors which also incorporates electronic motor brakes.
Electrical components according to UL/CSA Listings.

Technical Specifications

Edgeband thickness 0.4 – 12 mm (0.016" - 1/2” )
Coil cutoff maximum 0.8 x 45 mm
3.0 x 45 mm (PVC)
Edgeband height 12 - 60 mm (1/2" – 2 3/8 ")
Panel length min. 160 mm (6 3/8")
Panel width min. 65 mm (2 3/8")
Panel thickness - min.
- max.
8 mm (5/16")
55 mm (2 3/16")

Feed speed – two speeds 14 m/min (46 FPM) and 11 m/min
( 36 FPM ) when using the contour trimming unit the feed speed automatically adjusts to 11 m/min.
Feed motor 2.2 kw (3 HP)
Pressure section First roller driven, two rollers idle
End trim unit - two motors
Cutting speed
Straight cut max. .27 kw (1/3 HP ea)
12,000 RPM
5 x 45 mm (3/16" x 1 3/4")
Fine trimming unit
Tilting range
Cutter speed .55 kw (3/4 HP each)
0 - 25?
12,000 RPM
Profile trimming unit - top and bottom 0.3 kw (1/2 HP ea - two motors)
Electronic frequency changer
Total power required 7 kw
Amperage @ 230
@ 460 30 amps
15 amps
Machine length 5740 mm (18' 10”)
Machine width 1730 mm (68")
Working height 900 mm (35.5")
Total height 1600 mm (63")
Machine net weight (with all stations full) 2200 kg (4840 lbs.)

Electrical connection: 208/230 or 440/480 volt, 3-phase, 60 Hz.
Dust extraction: 2x 100 mm (4"), 1000 CFM.
Compressed air connection: 0.18 CFM per panel, 6 bar (85 PSI).

Automatic Height Adjustment with Top Pressure Beam for All Top Work Stations
PC-16 Program Control

Integrated Electronic Line Control System for Increased Reliability and Diagnostic Assistance

Automatic Magazine for Strip and Coil Feeding
• large coil table (800 mm diameter) with built-in rollers to allow for 3 mm PVC coils
• edge strip capacity from 0.4 mm to 8mm (0.016” – 5/16”)
• direction of glue roller reversible
• glue roller section is also retractable from fence line
• one large driven pressure roller with pneumatic pressure control
• two secondary rollers, all with controlled side pressure
• setting of pressure zone equipped with digital counter accurate to .1 mm (.004)
• strengthened precutter for cutting thick PVC edges from the coil; maximum 3 x 45 mm; precutting system equipped with air volume reservoir for on-demand activation required for short workpieces

Standard Gluing System
• heat-up time is twelve minutes
• no lubrication required – using high tech bearing system
• pneumatic locking of the unit for gluing the last two inches of the workpiece
• quick-change glue tank for easy maintenance and glue color change, if necessary
• glue temperature indication of both premelter and glue roller via LED thermostat display visible to operator
• infrared radiant glue heat zone control for optimum gluing strength
• Automatic temperature reduction if not run within 15 minutes. This feature lowers the temperature automatically to 150 degrees C.

Sound Cover
• equipped with three independent openings
• safety interlock system - when sound enclosure door is opened, corresponding work station shuts off
• end trimming, fine trimming, and top/bottom contour trimming motors are each equipped with electronic motor brakes to stop cutter rotation when hood is opened or when station is shut off at operator control panel

End Trimming Station
• straight/chamfer end trim unit equipped with two 0.27 kw (1/3 HP) 12,000 RPM motors; electronic motor brakes
• end trim unit utilizes drawing cut system for reduced blade projection when working on thick panels
• tooling also included
• program controlled indexing from straight to bevel end trimming

Fine Trimming Unit
• equipped with two .55 kw (3/4 HP) 12,000 RPM trimming motors
• electronic motor brakes
• horizontal and vertical tracing wheels with lateral location indexing via digital “Quickset” system calibrating to .1 mm (.004”)
• tilting from 0 - 25?
• each trimming motor is equipped with one dust hood and dust extraction hose
• equipped with two combination straight/radius cutterheads, including four knife carbide inserts set at shear angle for optimum surface quality finish; flush trimming possible up to 8 mm edge thickness; radius - 3 mm
• program controlled pneumatic indexing

Contour Trimming Unit
• for rounding front and trailing corners of workpieces with 3 mm PVC edgings
• includes two trimming motors 0.3 kw (1/2 HP) 12,000 RPM; electronic motor brakes
• equipped with 3 mm radius insert cutterheads - reversible

Scraping Unit with Knives
• for scraping of roughly trimmed thick PVC edges in order to remove the cutter marks
• quickly changeable
• tracing wheels both vertical and horizontal
• 3 mm radius reversible profile knives standard
• program controlled pneumatic indexing

Top and Bottom Buffing Unit
• top and bottom buffing motors for finishing of longitudinal edges
• two 2800 RPM polishing motors
• inclinable vertically and horizontally
• two buffing wheels included