Description:
!!! MAKE AN OFFER FOR THIS MACHINE !!!

Used HOMAG SE-9600 Single-Sided Edgebander / KLO-76 (2000)

Working units on left-hand side as seen from the direction of infeed.

Machine base manufactured with a continuous machine frame, off-trim collection channel, and automatic feed track system. Feed chain track equipped with 80 mm (3-5/32") wide chain plates, vulcanized rubber inserts, and centralized lubrication.

Top pressure beam equipped with double wide compound v-belt, motorized height adjustment for panel thickness and digital counter. Upper working heads of work stations linked to top pressure beam for automatic adjustment to panel thickness.

Outboard panel support with roller track extendible to 800 mm (31 1/2").

Technical
Specifications
working level 950 mm (37-13/32")
min. working width w/thickness 22 mm (7/8") 55 mm (2-5/32")
w/thickness 60 mm (2-3/8") 100 mm (3-15/16")
panel overhang 30 mm (1-1/8")
work piece min. 12 mm (15/32")
thickness max. 60 mm (2-3/8")
edge thickness strips 0.4 mm to 20 mm (0.16" to 25/32")
coils 0.3 mm to 3 mm (0.12" to 1/8")
processing limits strips 900 mm² (1.39 sq. in)
coils 135 mm² (0.19 sq. in)
operating voltage *480 volt 3-phase, 60 cycle
control voltage 24 volt
machine paint color gray RDS 240 80 05
variable feed speed 18 M/min to 24 M/min (59 ft/min to 78 ft/min)

Note: Max. adjusting range is not necessarily the appropriate working speed.

*Additional charge for voltage other than stated in specification.

Electrical equipment according to UL regulations.

In case of variations in technical specifications and capacities between the base machine and working units, the specifications and capacities given for the working units are to be considered as correct.

Conditions of floor at installation site must adhere to foundation plan.

Panel Pre-Heater
Homag Unit #2325
* quartz lamp for heating substrate edge before glue application
* for improved edge quality and optimum bonding

QA 34 Quick Melt Gluing Unit
Homag Unit #2123
* specially designed by Homag--the original innovator of the quick melt system
* lower reservoir unit is designed with only seven (7) wearing parts, which allows for ease of adjustment and reduces maintenance costs
* ideally suited for quick heat-up time and color changes
* one bolt secures lower unit to drive mechanism
* special coupling eliminates alignment of universal drive joint
* digitally displayed thermostat for both upper and lower unit, along with heated glue roller allow for excellent control of temperature for optimum bonding results
* heated glue roller
* individual adjustment for front and rear glue gates
* upper reservoir for glue granules
* glue roller diameter 34 mm (1-11/32")
* lower melting unit equipped with automatic control of glue level
? purge button * spill plate * dump gate

Glue Roller Drive
Homag Unit #2141
* eliminates glue charring on glue roller
• lengthens pot life of glue during idle running time of machine
* thermostatically controlled activation initiates glue roller drive when lower unit reaches melting temperature while feed track is stopped

Clamping Device for Glue Pot
Homag Unit #2143
• electro-pneumatic clamping of glue applicator at trailing edge of panel
• ensures consistent glue line

Glue Container Back-Off
Homag Unit #2145
• in case feed track stops

Multi-Purpose Magazine with Single Coil Horizontal Table
Homag Unit #2999
* capable of running coiled material, strips, and solid wood bands
* easily changed from one application to the next with the flip of a switch, conveniently located on the movable control pendant
* infeed angle 8°
* edge thickness 0.4 mm to 20 mm (0.016" to 25/32")
• edge height 12 mm to 65 mm (15/32" to 2-9/16")
* processing limits 900 mm2 (1.39 sq. in)
• min. edge length 260 mm (10-1/4")

Clipping Unit
Homag Unit #2445
* designed for today's popular use of thick coil PVC
* for use with single-roll table magazine
* max. edge thickness 3.5 mm (0.14")
* max. edge height 65 mm (2-9/16")
* PVC processing limits 135 mm2 (0.19 sq in)
* veneer processing limits 100 mm2 (0.15 sq in)
* max. roll diameter 900 mm (35-7/16")

Magazine Height Adjustment
Homag Unit # 2460
* with threaded spindle adjustment and digital readout
* adjustable +/- 10 mm (+/- 13/32")

Pressure Zone for Gluing Section Type C
Homag Unit #2507
* one (1) driven pressure roller 150 mm (5-29/32") diameter
* six (6) secondary pressure rollers 70 mm (2-3/4") diameter
* with pneumatic pressure control for straight edges
* centralized manual adjustment for edgeband thickness with digital mechanical counter


Snipping Unit HL 05
Homag Unit #3054
* for straight and chamfer snipping
* with two (2) motors, 0.4 kW, 200 cycle, 12000 rpm
* equipped with self-aligning industrial grade ball slides and rails
* adjusting device for manual resetting from chamfer to straight snipping
* edge thickness straight max. 20 mm (25/32")
chamfer max. 3 mm (1/8")
* max. edge height 65 mm (2-9/16")
* with two (2) TCT saws 120 mm x 3.2 mm, z = 20
? electronic frequency invertor for control of RPM and motor braking

Adjustment Chamfer, Straight
Homag Unit #3114
* for automatic re-setting from straight snipping to chamfer snipping
* manual motor adjustment required in case of modifications of edge thickness

Top & Bottom Flush Trimming Unit
Homag Unit #3209
• motors positioned one above the other, 1.5 kW, 200 cycle, 12000 rpm
• angle adjustment +/- 1°
* with two (2) carbide tipped trimming cutters, 70 mm x 25 mm,
HSK 25, z = 4
• motors running against direction of feed
• motors manually adjustable with digital mechanical counters
• height adjustment with top pressure beam
? electronic frequency invertor for control of RPM and motor braking

Top & Bottom Bevel Trimming Unit
Homag Unit # 3216/3295
• motors positioned either side of column, 0.4 kW, 200 cycle,
12000 rpm
* max. panel thickness 60 mm (2-3/8")
* tilting range 0° to 30°
* with two (2) replaceable insert trimming cutters 70 mm x 14.3 mm, HSK 25, z = 4
* motors running against direction of feed
* motors and side copy wheels manually adjustable with digital mechanical counters
* height adjustment with top pressure beam
• with quick disconnect electrical plugs for both motors #3295
? electronic frequency invertor for control of RPM and motor braking

Profile Trimming Unit, FF 12
Homag Unit #3503 (P)
• for cross-processing of postformed/softformed parts on leading and trailing edges
• top and bottom
• adjusting device with manual eight-fold turret stop
* with four (4) motors, each 0.04 kW, 200 cycle, 12000 rpm
* max. edge thickness 6 mm (1/4")
* max. panel thickness 40 mm (1-9/16") with processing
panel thickness 60 mm (2-3/8") without processing
* min. panel length 120 mm (4-23/32") single sided
* with quick motor change device
• equipped with tool chuck HSK 25
• panel spacing at 20 M/min (65 ft/min), approx. 600 mm (23-5/8")
* without tooling
? electronic frequency invertor for control of RPM and motor braking

Pneumatic Adjustment for Profile Trimming Unit
Homag Unit #3536
* for electro-pneumatic positioning of unit into or out of processing area

Noise Reduction Enclosure
Homag Unit #0415/0425
* for edge trimming section
* with centralized dust extraction ports
* with viewing windows
• illuminated for ease of operator inspection

Profile Scraping Unit
Homag Unit #4510
* tracing from top, bottom and side
* for chamfering or rounding of pre-trimmed PVC edges
* pneumatically controlled blowing nozzles
* max. edge thickness 3 mm (1/8")
* panel thickness 12 mm to 60 mm (15/32" to 2-3/8")
* unit laterally adjustable by max. 50 mm (1-31/32")
* collection box for PVC shavings
* height adjustment with top pressure beam
* without tools
• manually adjustable with digital mechanical counters


Pneumatic Adjustment for Profile Scraping Unit
Homag Unit #4522
* for electro-pneumatic positioning of unit into or out of processing area

Top & Bottom Edge Buffing Unit with Oscillation
Homag Unit # 4402
* with two (2) motors .25 kW, 60 cycle, 2850 rpm
* max. panel thickness 60 mm (2-3/8")
* with vertical, horizontal and angle adjustment
* equipped with two (2) cloth buffing wheels 150 mm x 50 mm x 25 mm (5-29/32" x 1-31/32" x 31/32")

Homatic Electronic Control
Homag Unit #6202
* control with programmable memory (PLC)
* Homatic 2000 with indication of all inputs and outputs by means of luminous diodes
* integrated line control for remote control of processing units
* multi-tasking control of PLC for precise unit operation
* part number in machine at choice
* compatible interface to all Homatic input systems
* recommended environmental temperature
min. +5° C (41° F), max. +35° C (95° F)


Monitor Input NC 21
Homag Unit # 6313
* user friendly Homatic monitor input for control and administration of processing programs of a machine

Hardware
* industrial computer 68040, 16 MByte RAM
* one (1) PCMCIA storage card, 170 MByte for storage of approx. 20,000 operation programs
• one (1) open slot for spare PCMCIA card for data back up
* multi-tasking real time operation system OS-9, with windows style display system
• windows-standard menu for program selection
• menu driven program generation
* bus connection (VME-Bus) for PLC, for quick and safe data transmission
* 10.4" LCD flat panel display with PC compatible keyboard, installed in operator console
* network connectable (Ethernet*)
* possible telephone diagnostics
• line control data transmission via fiber optic cables for increased processing speed and isolation from high frequency noise

* Additional hardware and software required.

Software
* simple programming of operation programs
* off-set allowance for compensation of tool wear in conjunction with stepless axes
* production according to operation programs
* PLC ladder diagrams can be displayed on machine monitor
• modem available for customer's use for remote diagnostic purposes
• modem must be returned within six (6) months of acceptance of machine at customer's facility or purchased under separate maintenance agreement contract
• two (2) telephone lines must be provided by the customer at the machine, one (1) telephone line to be equipped with a receiver