Description:
!!! MAKE AN OFFER FOR THIS MACHINE !!!

Used HOMAG SE-9600 Single-Sided Edgebander / KLO-76/QA/20 (1998)

Working units on left-hand side as seen from the direction of infeed.

The machine base is manufactured with a continuous machine frame, off-trim collection channel, automatic feed track system. The feed chain is equipped with 80 mm (3-5/32") wide chain plates, vulcanized rubber inserts, and centralized lubrication.

Top pressure beam is equipped with double wide compound v-belt with motorized height adjustment for panel thickness with digital counter. Upper working heads of work stations linked to top pressure beam for automatic adjustment to panel thickness.

Outrigger panel support with roller track extendible to 800 mm (31 1/2").

Technical
Specifications
working level 950 mm (37-13/32")
min. working width w/thickness 22 mm (7/8") 55 mm (2-5/32")
w/thickness 60 mm (2-3/8") 100 mm (3-15/16")
panel overhang 30 mm (1-1/8")
work piece thickness min. 12 mm (15/32")
max. 60 mm (2-3/8")
edge thickness strips 0.4 mm to 20 mm (0.16" to 25/32")
coils 0.3 mm to 3 mm (0.12" to 1/8")
processing limits strips 900 mm2 (1.39 sq. in)
coils 135 mm2 (.19 sq. in)
operating voltage 480 volt 3-phase, 60 cycle
control voltage 24 volt
machine paint color gray RDS 240 80 05
variable speed 18 M/min to 24 M/min 59 ft/min to 78 ft/min

Note: Max. adjusting range is not necessarily the appropriate working speed.

Electrical equipment according to UL regulations.

In case of variations in technical specifications and capacities between the base machine and working units, the specifications and capacities given for the working units are to be considered as correct.

Conditions of floor at installation site must adhere to foundation plan.
Panel Pre-Heating
Homag Unit # 2325
* quartz lamp for heating of substrate edge before glue application
* used for improved edge quality

QA 34 Quick Melt Gluing Unit
Homag Unit #2123
* lower reservoir unit designed with only seven (7) wearing parts, for ease of adjustment and reduction of maintenance costs
* ideally suited for quick heat-up time and color changes
* one bolt secures lower unit to drive mechanism
* special coupling eliminates alignment of universal drive joint
* digitally displayed thermostats for both upper and lower units
• heated glue roller for precise control of temperature for optimum bonding results
* individual adjustment of front and rear glue gates
* upper reservoir for glue granules
* glue roller diameter 34 mm (1-11/32")
* lower melting unit equipped with automatic control of glue level
? purge button - spill plate - dump gate

Glue Roller Drive
Homag Unit #2141
* eliminates glue charring on the glue roller and lengthens the pot life of the glue during idle running time of the machine
* because it is thermostatically controlled, it activates to keep the glue roller drive continuing when lower unit has reached its melting temperature and the feed track is stopped

Clamping Device for Glue Pot
Homag Unit #2143
• electro-pneumatic clamping of glue applicator at panel's trailing edge

Glue Container Back-Off
Homag Unit #2145
• in case feed track stops


Multi-Purpose Magazine
* ideally suited for the flexible needs of today's customers
* capable of running coiled material , strips, and solid wood bands
* can easily change from one application to the next with the flip of a switch, conveniently located on the movable control pendant
* infeed angle 8°
* edge thickness 0.4 mm to 20 mm (0.016" to 25/32")
• edge height 16 mm to 65 mm (5/8" to 2-9/16")
* processing limits 900 mm2 (1.39 sq. in)
* min. edge length 260 mm (10-1/4")

Magazine Height Adjustment
Homag Unit # 2460
* with threaded spindle adjustment
* adjustable +/- 10 mm (+/- 13/32")

Clipping Unit
Homag Unit # 2445
* designed for today's popular use of thick coil PVC
* for use with single-roll table magazine
* max. edge thickness 3.5 mm (0.14")
* max. edge height 65 mm (2-9/16")
* PVC processing limits 135 mm2 (0.19 sq. in)
* veneer processing limits 100 mm2 (0.15 sq. in)
* max. roll diameter 800 mm (31-1/2")

Pressure Zone for Gluing Section Type C
Homag Unit # 2507
* one (1) driven pressure roller 160 mm (6-5/16") diameter
* six (6) secondary pressure rollers 70 mm (2-3/4") diameter
* with pneumatic pressure control for straight edges
* centralized manual adjustment for edgeband thickness


Snipping Unit HL 05
Homag Unit # 3054
* for straight and chamfer snipping
* with two (2) motors, 0.4 kW, 200 cycle, 12000 rpm
* equipped with self-aligning industrial grade ball slides and rails
* adjusting device for manual resetting from chamfer to straight snipping
* edge thickness straight max. 20 mm (25/32")
chamfer max. 3 mm (1/8")
* max. edge height 65 mm (2-9/16")
* max. snipping depth softforming 20 mm (25/32")
* with two (2) TCT saws 120 mm x 3.2 mm, z = 20
? electronic frequency invertor for control of motor speed and braking

Adjustment Chamfer, Straight
Homag Unit # 3114
* for automatic re-setting from straight snipping to chamfer snipping
* manual motor adjustment required in case of modifications of edge thickness

Flush Trimming Unit
Homag Unit # 3209
* top and bottom
* with two (2) motors positioned one above the other, 1.5 kW,
200 cycle, 12000 rpm
* max. edge thickness 20 mm (25/32")
* panel thickness 12 mm to 60 mm (15/32" to 2-3/8")
* angle adjustment +/- 1°
* with two (2) carbide tipped trimming cutters, 70 mm x 25 mm,
HSK 25, z = 4
* motors running against direction of feed
* motors manually laterally adjustable with digital mechanical counters
* height adjustment with top pressure beam
? electronic frequency invertor for control of motor speed and braking


Bevel Trimming Unit
Homag Unit # 3216
* top and bottom
• with two (2) motors, each 0.4 kW, 200 cycle, 12000 rpm
* max. panel thickness 60 mm (2-3/8")
* tilting range 0° to 30°
* with two (2) replaceable insert trimming cutters 70 mm x 14.3 mm, HSK 25, z = 4
* motors are running against direction of feed
* motors and side copy wheels are manually adjustable with digital mechanical counters
* height adjustment with top pressure beam
? electronic frequency invertor for control of motor speed and braking

Quick Disconnect Electrical Plugs
Homag Unit # 3295
* for motor

Motor Bracket For Tool Change
Homag Unit # 9999

Profile Trimming Unit, FF 12
Homag Unit #3512
• for cross-processing of postforming/softforming parts on leading and trailing edges
• top and bottom
* with four (4) motors, each 0.4 kW, 200 cycle, 12000 rpm
* max. edge thickness 6 mm (1/4")
* max. panel thickness 40 mm (1-9/16") with processing
panel thickness 60 mm (2-3/8") without processing
* min. panel length 120 mm (4-23/32") single sided
* with quick motor change device
• equipped with tool chuck HSK 25
* without tooling
? electronic frequency invertor for control of motor speed and braking

Pneumatic Adjustment for Profile Trimming Unit Homag Unit #3536
* for electro-pneumatic positioning of profile trimming unit into or out of processing area


Noise Reduction Enclosure
* for edge trimming section
* with centralized chip extraction port
• with partition wall between working units
* illuminated for ease of operator inspection
* with viewing windows

Profile Scraping Unit
Homag Unit #4510
* tracing from top, bottom and side
* for chamfering or rounding off of pre-trimmed PVC edges
* pneumatically controlled blowing nozzles
* max. edge thickness 5 mm (3/16")
* panel thickness 7 mm to 60 mm (9/32" to 2-3/8")
* unit laterally adjustable by max. 50 mm (1-31/32")
* collection box for PVC shavings
* height adjustment with top pressure beam
* without tools
• manually adjustable with digital mechanical counters

Pneumatic Adjustment for Profile Scraping Unit
Homag Unit #4522
* for automatic adjustment of profile scraping unit into and out of working area

Open Space
• 130 mm (5-1/8")

Edge Buffing Unit with Oscillation
Homag Unit # 4402
* top and bottom
* with two (2) motors .25 kW, 60 cycle, 2850 rpm
* max. panel thickness 60 mm (2-3/8")
* with vertical, horizontal and angle adjustment
* equipped with two (2) cloth buffing wheels 150 mm x 50 mm x 25 mm
• oscillation device


Homatic Electronic Control
Homag Unit #6202
* control with programmable memory (PLC)
* Homatic 2000 with indication of all inputs and outputs by means of luminous diodes
* integrated line control for remote control of processing units
* multi-tasking control of PLC for precise unit operation
* part number in machine at choice
* compatible interface to all Homatic input systems
* recommended environmental temperature
min. +5° C (41° F), max. +35° C (95° F)

Monitor Input NC 21
Homag Unit # 6313
* user friendly Homatic monitor input for control and administration of processing programs of a machine

Hardware
* industrial computer 68040, 8 MByte RAM
* one (1) fixed-disk system, 130 MByte for store of approx. 20,000 operation programs
* multi-tasking real time operation system OS-9, with windows style display system
• windows-standard menu for program selection
• menu driven program generation
* bus connection (VME-Bus) for PLC, for quick and safe data transmission
* 11" LCD flat panel display with PC compatible keyboard, installed in operation desk
* telephone diagnostic compatible
• line control data transmission via fiber optic cables for increased processing speed and isolation from high frequency noise


Software
* simple programming of operation programs
* off-set allowance for compensation of tool wear in conjunction with stepless axes
* production according to operation programs
* PLC plan diagnostic on machine monitor
• modem available for customer's use for remote diagnostic purposes
• modem must be returned within six (6) months of acceptance of machine at customer's facility or purchased under separate maintenance agreement contract
• two telephone lines must be provided by the customer at the machine, one telephone line to be equipped with a receiver