Description:

Used BRANDT KDF 660 2C Servo Automatic Edgebander (2007)
w/ nested tracing system & DOUCET BT-2030 Return Conveyor

-- Very low hours: less than 400 hrs --

Also available with DELIVERY, INSTALLATION & W/ WARRANTY (please contact us f. pricing)

PC-20 Program Control
- PC: Industrial PC, 600 Mhz, Front side USB port.
- Memory: 256 Mb ram, 1 Gb Flash Card.
- Screen: 12.1” Color, 800 x 600 pixel, Active TFT Screen.
- Internal modem for remote diagnostic link.

Motorized top pressure beam for panel thickness adjustment.

Smooth upper pressure rollers.

Automatic feed track lubrication system.

Adjustable in feed fence.

Joint trimming unit for pre-trimming the work piece edge prior to processing.

Quick melt granulate glue application system with twelve minute heat-up time.

Quick-change glue tank for easy maintenance and glue color change, if necessary.
I
nfrared radiant quartz heating unit between glue roller and pressure zone for optimum gluing strength.

Program controlled positioning of the pressure zone. First pressure roller driven and three idle pressure rollers.

Double motor end trimming unit with straight and chamfer capability. Chamfer up to 15?.

Program controlled indexing from straight to bevel end trimming.

Flush trimming unit with two position vertical indexing and program controlled pneumatic indexing of the unit. Diamond cutters.

Fine trimming unit with DFC cutter head technology, servo motor control for side copy positioning and to edge thickness for the unit. Auto tilt. Radius / straight DFC cutters included. This unit provides superior dust flow control of the trimmed chips and provides precise trimming due to location of the vertical copy rollers. Diamond cutters with 2mm radius. Three roller copy system

Contour trimming unit for profile corner trimming.

Sound enclosure with centralized dust extraction outlet.

Scraping unit for rigid PVC edges. Top copy shoe for nested parts. Program controlled indexing.

Surface scraping unit.

Buffing unit.

Electronic frequency changer for all trimming motors.

Electrical components according to UL/CSA Listings.

Technical Specifications
Edge band thickness 0.4 – 12 mm (0.016" - 1/2” )
Coil cutoff maximum 0.8 x 60 mm
3.0 x 45 mm (PVC)
Edgeband height 12 - 65 mm (1/2" – 2 9/16 ")
Panel length min. 160 mm (6 3/8")
Panel width min. 65 mm (2 3/8")
Panel thickness
- min. 8 mm (5/16")
- max. 60 mm (2 3/8")

Feed speed – two speeds 16 m/min (52 FPM) and 11 m/min
( 36 FPM ) when using the contour trimming unit.
Feed motor 2.2 kw (3 HP)
Joint trimming unit – two motors 2.2 kw ( 3 HP each )
Cutting speed 12,000 RPM

Pressure section First roller driven, three rollers idle
End trim unit - two motors .35 kw (1/2 HP ea)
Cutting speed 12,000 RPM
Straight cut max. 12 x 40 mm (1/2" x 1 5/8")
Flush trimming unit .55 kw (3/4 HP each
Cutter speed 12,000 RPM
Fine trimming unit-auto tilt .55 kw (3/4 HP each)
Cutter speed 12,000 RPM

Profile trimming unit - top and bottom 0.3 kw (1/2 HP ea - two motors)
Total power required 18.5 kw
Amperage @ 230
@ 460 80 amps
40 amps
Machine length 6360 mm (20' 10”)
Machine width 1730 mm (68")
Working height 900 mm (35.5")
Total height 1600 mm (63")
Machine net weight 2800 kg (6160 lbs.)

Electrical connection: 208/230 or 440/480 volt, 3-phase, 60 Hz.
Dust extraction: 1x 120 mm (4 3/4"), 1x 160 mm ( 6 1/4” ), 1x 100 mm ( 4” ) 1800 CFM.
Compressed air connection: 0.18 CFM per panel, 6 bar (85 PSI).

PC-20 Program Control

Motorized top pressure beam with smooth rollers


Joint Trimming Unit
• pre-trimming of the workpiece edge prior to gluing
• two motors, 3 HP each, 12,000 RPM
• one motor clockwise rotation, one counter-clockwise
• vertical spindle adjustment via digital settings
• horizontal positioning via electro-pneumatic control
• dust extraction hood included with 120 mm diameter outlet ( 4 ¾ “)
• diamond cutter heads.

Automatic Magazine for Strip and Coil Feeding
• large coil table (800 mm diameter) with built-in rollers to allow for 3 mm PVC coils
• edge strip capacity from 0.4 mm to 12 mm (0.016” – 1/2”)
• direction of glue roller reversible
• glue roller section is also retractable from fence line
• one large driven pressure roller with pneumatic pressure control
• three secondary rollers, all with controlled side pressure
• program controlled setting of pressure zone
• strengthened pre-cutter for cutting thick PVC edges from the coil; maximum 3 x 45 mm; precutting system equipped with air volume reservoir for on-demand activation required for short workpieces

Quick Melt Gluing System
• heat-up time is ten minutes
• hopper feeding gluing system
• no lubrication required – using high tech bearing system
• pneumatic locking of the unit for gluing the last two inches of the workpiece
• quick-change glue tank for easy maintenance and glue color change, if necessary
• glue temperature indication of both pre-melter and glue roller via LED thermostat display visible to operator
• infra-red radiant glue heat zone control for optimum gluing strength. Automatic temperature reduction if not run within 15 minutes. This feature reduces the temperature automatically to 150 degrees C.

Sound Cover
• equipped with three independent openings
• safety interlock system - when sound enclosure door is opened, corresponding work station shuts off
• end trimming, fine trimming, and top/bottom contour trimming motors are each equipped with electronic motor brakes to stop cutter rotation when hood is opened or when station is shut off at operator control panel

End Trimming Station
• straight/chamfer end trim unit equipped with two 0.35 kw (1/2 HP) 12,000 RPM motors; electronic motor brakes
• end trim unit utilizes drawing cut system for reduced blade projection when working on thick panels
• tooling also included
• program controlled indexing from straight to bevel end trimming

Flush Trimming Unit
• equipped with two .55 kw (3/4 HP) 12,000 RPM trimming motors
• electronic motor brakes
• vertical tracing wheels with two position vertical indexing via program control.
• each trimming motor is equipped with one dust hood and dust extraction hose
• equipped with two straight diamond cutter heads, flush trimming possible up to 12 mm edge thickness.
• program controlled pneumatic indexing

Fine Trimming with DFC Cutter Head and Servo motor control
• equipped with two .55 kw (3/4 HP) 12,000 RPM trimming motors
• electronic motor brakes
• horizontal and vertical tracing wheels
• auto tilt feature
• each trimming motor is equipped with one dust hood and dust extraction hose
• equipped with two radius diamond cutter heads, including four knife carbide inserts.
• servo motor controlled positioning of the work units and side copy to edge thickness. R= 2mm

Contour Trimming Unit
• for rounding front and trailing corners of workpieces with 3 mm PVC edgings
• includes two trimming motors 0.3 kw (1/2 HP) 12,000 RPM; electronic motor brakes
• equipped with 2 mm radius cutter heads – reversible
• pneumatic two position indexing for use with two different edge thicknesses

Scraping Unit with Knives
• for scraping of roughly trimmed thick PVC edges in order to remove the cutter marks
• Quickly changeable
• Top tracing shoe for nested parts.
• Tracing wheels both vertical and horizontal
• 3 mm radius reversible profile knives standard
• program controlled pneumatic indexing

Surface Scraping Unit
• Flat knives remove any unwanted material from the trimmed / scraped edge

Top and Bottom Buffing Unit
• top and bottom buffing motors for finishing of longitudinal edges
• two 2800 RPM polishing motors
• inclinable vertically and horizontally
• two buffing wheels included

IN CASE OF INCOMING MAIN VOLTAGE FLUCTUATIONS OF MORE THAN +5% / - 5% OF MACHINE CONNECTED VOLTAGE, A VOLTAGE STABILIZER MUST BE INSTALLED BY THE CUSTOMER ON THE INCOMING POWER CONNECTION.